Plenty of houses in Highland Park Survey still carry their first mortise locks and brass knobs, and they are worth keeping. We service that hardware so it turns freely again, find matching parts where they exist, and only suggest replacement when a piece genuinely cannot be brought back. Character stays; the door locks. Nearby, we also work in Brock Gardens, Bullocks Corners, Glenwood Heights and Greensville.
Same fees day or night · Highland Park Survey
HamiltonOntario
Every square is one home in a hundred.
Highland Park Survey
Residents and business owners in Highland Park Survey can use this list to find the service that fits, then read what it involves before anyone comes out. Emergency openings are here. So are rekeys, lock changes, deadbolt and high-security upgrades, commercial door hardware, master keys, safes and key cutting.
Seized & Jammed Lock Opening, Safe Installation & Servicing, Master Key System Design, Break-In Damage Lock…
Residents and business owners in Highland Park Survey can use this list to find the service that fits, then read what it involves before anyone comes out. Emergency openings are here. So are rekeys, lock changes, deadbolt and high-security upgrades, commercial door hardware, master keys, safes and key cutting.
Job sheet1 of 4
ServiceBroken Key Extraction
Job sheet2 of 4
ServiceBreak-In Damage Lock Repair
Job sheet3 of 4
ServiceSeized & Jammed Lock Opening
Job sheet4 of 4
ServiceSmart Lock Installation
Deadbolts differ in how far the bolt travels, how hard the bolt is, whether the cylinder guard spins free under a wrench and whether the housing shrugs off a hammer. High security deadbolts do well on all four, and we can show you the difference in hand.
Layer 1The key
You jiggle the key a little and the old deadbolt opens even when the cut does not look quite right. If your worn key can do that, you wonder what a stranger with the right tools could do.
Layer 2The cylinder
The lever on the side door droops toward the floor and rattles in your hand. The latch no longer springs back on its own, so the door drifts open behind you unless you pull it shut and check it twice.
Layer 3The bolt and strike
Someone tried the door last winter. The frame took it, but the strike plate is bent, one screw hole is stripped, and the bolt sits in the pocket at a slight angle.
Layer 4The door and frame
The back door looks closed until you touch it. The edge is crushed where a bar went in, the latch is bent sideways, and the door swings free with a gentle push no matter how you turn the key.
High Security Locks. You jiggle the key a little and the old deadbolt opens even when the cut does not look quite right.
Request a visitUsually. Laid end to end, the halves show the full set of cuts and identify the blank, and a locksmith reads them with a gauge and cuts a fresh key to those depths on a code machine. That is better than tracing the broken blade on a duplicator, because a worn key copied is a worn key repeated. If a spare or the key code exists, that is used instead.
A security strike is a heavier plate with a formed steel pocket that wraps around the bolt instead of leaving it in bare wood. It is set into the jamb and fixed with long screws, typically three inches, that pass through the jamb and the shim space into the framing, with the longest screws placed nearest the door stop where the bolt bears. Manufacturers specify the pocket depth so the bolt extends fully. The result spreads a kick across the wall stud rather than two small screws.
Try the key while gently pushing, pulling and lifting the door. If it frees up in one position, the bolt is being pinched by the frame and the door is the cause. If nothing changes, look at the key: does it go fully in and refuse to turn, or spin freely? The first points to the cylinder, the second to the tailpiece behind it. Tell the locksmith which you found and the right parts come in the van.
Most residential doors have the standard preparation these locks are designed around: a large hole for the lock body, a smaller one in the edge for the bolt, and a thickness between roughly 35 and 45 millimetres. The locksmith measures all three plus the backset before recommending a model. Thicker doors take an extension kit, thin or glass-panelled doors and older doors with a mortise pocket call for a particular model or some preparation, and all of that is sorted out before the box is opened.
On-site assessment
Reach a locksmith serving Highland Park Survey right now
(289) 203-6954, open 24/7.
On-site assessment preferred · (289) 203-6954, open 24/7